Waterproofing top of joists. By Bill (London, ON) Twenty-one years ago I built a cedar deck. Or what about Blue Seal Waterproof Rubber Membrane? Or perhaps tar paper is a better choice? Looking forward to your comments! I am looking to install privacy screens on my concrete patio. I just want to put up two 6x6 posts with Titan Wood Post. View Full Version: Blue seal (waterproof rubber membrane) over durock, overkill? Newbieonhomes., 09:26 AM. I am back to the bath project again. I am ready to installing the shower walls over an acrylic shower base. This is a shower stall, separated from the tub. I'll be putting durock on all walls.
Blueskin® WP 200 is a self-adhering composite membrane consisting of an SBS rubberized asphalt compound, integrally laminated to a blue, high-density polyethylene film. The membrane is specifically designed for self-adhering to a prepared substrate, and provides a high-performance waterproofing barrier. Features
Packaging
*Based on 65 mm laps both side and end laps |
| ||||||||||||||||||||||||
| ||||||||||||||||||||||||
Preparation:
Read all label instructions before proceeding. Be sure surfaces are clean and dry before the coating application. Pressure wash when possible using pure water. Be sure surfaces are clean and completely dry before the coating application. Do not use any soaps, or detergents. Remove all loose paint, tar, dirt, oil, and grease leaving surface clean and completely dry. In certain situations a shot-blaster may be needed to help clean and roughen the surface. Always run a test patch first in an inconspicuous area to ensure that proper adhesion and drying occurs and the product works to your satisfaction. All cracks, joints (1/8″ or less), and seams should be caulked with a non-silicone, paintable caulk or Ames® Blue Max® Trowel Grade coating and filler. For larger cracks (1/8″ or larger) fill with a cementitious filler. Make sure surface is as smooth as possible. For best results and adhesion, it is ideal to apply coating over a bare surface void of paint or residue of any kind. Product comes ready to use, no mixing or stirring required. For newly poured concrete, you must allow at least 30 days for complete dry and cure time before applying product.
Liquid Rubber Waterproofing Membrane
Tools:
Foundation Waterproofing Rubber Membrane
Ames® Blue Max® or Ames® Block & Wall® Liquid Rubber can be applied with a paint brush, a low nap roller or a commercial/industrial airless sprayer. You may also need Ames® Peel & Stick™ Seam Tape, as well as scissors, a utility knife and a standard paint tray. For larger commercial jobs, we recommend an airless sprayer. Call toll free at 1-888-345-0809 with questions or for specific sprayer specifications. Click Here for Sprayer Specifications
Application:
Steps 1: Directions are the same for both Ames® Blue Max® and Block & Wall® Liquid Rubber. They do not need a primer. Caulk all cracks greater than 1/8″ wide with Ames® Blue Max® Trowel Grade.
Step 2: Surfaces with joints, cracks, or where two unlike surfaces come together, require Ames® Peel & Stick™ Seam Tape (PS250, PS450 or PS650) to provide some additional strength and reinforcement. It is important to seam tape all joints and cracks to avoid future cracking and leaking. Prime all surfaces generously with Ames® Blue Max® prior to setting the Seam Tape in place.
Step 3: Apply a liberal topcoat of Ames® Blue Max® or Block & Wall™ Liquid Rubber over the Seam Tape and allow to cure.
Important: Ames® Liquid Rubbers must be protected from the suns UV rays if exposed. Top coat with Ames Paint & Prime® or similiar Ames® Acrylic coatings.
Estimated Coverage:
We recommend three gallons per 100 square feet for water containment. No need to shake or stir prior to use. The application must be applied in a continuous, unbroken seal of a minimum dry thickness of no less than 30 mils (the thickness of a dime). Two coats minimum, three to four is superior. More coats equal longer life. Rough surfaces will require additional product and drying time.
Weather & Drying Guidelines:
Both Ames® Blue Max® and Block & Wall® Liquid Rubber are best applied between 50° to 90° F (10° to 32° C) on warm dry surfaces. For exterior applications apply when the streets are dry, the sun is in the sky and no inclement weather is forecast. Starts to dry in 30 minutes to 2 hours, depending on thickness of application and weather. It continues to cure for up to 2 weeks. A slight tack is normal after drying. Ames® Blue Max® may be re-coated or top coated when it is dry to the touch. Low temperatures, high humidity, and evening and morning dew will require increased drying/curing time.
Clean-up, Storage, and Disposal:
Clean tools and small spills with water. Store unused product in its original container, tightly sealed and protected from freezing. Dispose of this product in accordance with local, state, or federal requirements.
Can be used in Conjunction with:
Ames® Blue Max® trowel-grade and works well as a primer and waterproofing membrane for Ames® Safe-T-Deck®, Ames® Snow Seal®, Ames® Maximum-Stretch®, Ames® Block & Wall®, Ames® Iron Coat® and many other coatings. Ames® Blue Max® must be top coated for UV protection in exterior applications.
Blue Max®
Ames® Blue Max® is a special blend of adhesive, high strength elastomeric liquid rubber. It is a new, impenetrable, rubber technology for waterproofing in extreme wet situations such as below grade foundations, basement walls and a base coat for certain roof types.
Block & Wall® Liquid Rubber
Ames® Block & Wall® Liquid Rubber is a blend of adhesive, high strength, elastomeric, liquid rubber. It is designed for waterproofing in extreme situations.
Peel & Stick™ Seam Tape
Ames® Peel & Stick™ Seam Tape is a self-adhesive, contouring seam tape for reinforcement over seams and cracks and around vents. Easy to apply.